Altec Lansing PT7031 Betriebsanweisung PDF herunterladen (Seite 10)

Default Preprogrammed Remote Control Codes

Your PT7031 remote control is preset to the default codes listed in the

table below. If your component is not listed please consult the list in

the Preprogrammed Remote Control Codes section.You can also use the

earch procedure in the Searching for Remote Control Codes section of

this manual.

Programming Device Remote Control Codes

Find the brand, model and code number of your components in the

Preprogrammed Remote Control Codes section of this manual, then

follow these steps:

• While holding down the PROGRAM button, press the button for the

device to be programmed, i.e.,TV or DVD or CAB/SAT or AUX.

• The Status LED illuminates.

• Release both buttons.

• Enter the CODE NUMBER using the numeric buttons on the remote.

If the CODE NUMBER is valid the LED will flash twice and then turn

off, indicating the code has been programmed. If the code number is

not valid the LED flashes twice and turns on;

• Check to see that the remote can control the device that was

programmed by using the CH+/– or similar button to control the

device that was programmed. If it does not control the device, repeat

this procedure.

Note: If you want to leave the setup mode, press the device button

(TV, SAT/CAB, DVD, etc.). If you do not press any buttons after 10

seconds, SETUP MODE exits automatically.

Searching for Remote Control Codes

If you cannot find a code n

umber fr

om the Preprogrammed Remote

ontrol Codes section of this manual that matches your equipment, the

PT7031 remote can search its database for a suitable control code from

the codes programmed into the remote. The PT7031 remote control

will find the best possible component code f

or an

y audio sour

ce.

To search for codes follow these steps:

• Turn the device (TV, SAT/CAB, DVD, AUX, etc) that you wish to locate

the r

emote contr

ol code for to the on position.

• On the PT7031 remote press and hold the PROGRAM button while

essing the device button you wish to search for (TV, SAT/CAB, DVD,

AUX, etc).

• The STATUS LED on the PT7031 will illuminate and remain on.

• Press and release the PROGRAM button again. The LED will flash to

indicate that the remote has entered the search mode.

• Aiming the PT7031 remote at the device you want to control

repeatedly and slowly press and release the POWER button. The

PT7031 will send a different POWER code to the device each time

the P

OWER button is pressed.

•

Once the device you wish to control powers off, immediately stop

pressing the POWER button and press the device (TV, SAT/CAB, DVD,

AUX, etc) button again.

• The PT7031 should now be programmed to control your device.

• You can verify this by turning the device on, and entering other

applicable commands such as PLAY or STOP for a DVD player or

CHANNEL +/– for a SAT box.

Note: While the POWER button was used for searching here, you can

use other commands such as the PLAY button for devices that do not

ave a POWER button. In this case the PT7031 uses the PLAY button to

search. Simply use the PLAY button instead of the POWER button as

described below ensuring that the device you wish to control is ready

to enter the play mode and has a DVD or tape loaded, is on, etc.

emote Button

nitial code

quipment

TV 082 Philips TV

SAT/CAB 039 Philips Cable Box

AUDIO 900 Altec Lansing PT7031

AUX 144 Panasonic VCR

DVD 124 Sony DVD

1 2 ... 5 6 7 8 9 10 11 12 13 14 15 ... 43 44

Kommentare zu diesen Handbüchern

Keine Kommentare

Altec Lansing PT7031 Betriebsanweisung Seite 10

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Lautsprecher Altec Lansing PT7031